STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT

IMR OpenIR

	STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT
	Li Yongkui 1; Quan Chunyi 2; Lu Shanping 1; Jiao Qingyang 2; Li Shijian 2; Sun Zhonghai 2
通讯作者	Lu Shanping(shplu@imr.ac.cn)
	2016-03-11
发表期刊	ACTA METALLURGICA SINICA
ISSN	0412-1961
卷号	52 期号:3 页码:281-288
摘要	Weld deformation of the thin-wall weldment used in fighter aircraft not only hinders its subsequent procedure of fabrication and assembling, but also reduces its fatigue strength. As a result, weld deformation shortens its service life essentially. Dustpan deformation is always produced in the thin-wall weldment after multiple pass weld. In this work, combining with the experiment, the finite element method was adopted to analysis the deformation of the thin-wall weldment by multiple-pass weld and its shape correction by post weld heat treatment. For obtaining the fundamental properties such as thermal parameters and mechanical parameters of TA15 titanium alloy, a series of experiments were conducted at room temperature and high temperatures. Additionally, creep behaviors of TA15 titanium alloy were studied at the temperatures of 500, 550, 600, 650, 700 and 750 degrees C, and the parameters of creep constitutive equations of the alloy were obtained with considering the analysis of post weld heat treatment. A thermal coupled temperature-displacement analysis for welding and post weld heat treatment was performed on a three dimensional shell model of protective grille. Experiments of multiple-pass weld and post weld heat treatment were used to testify the reliability of the finite element model of welding and post weld heat treatment. With using the reliable finite element model, the parameters of heat treatment were studied. The study indicates that, the fabrication on the crossing of structure section and fillet after fillet-wallboard weld leads the compression deformation release along the fillet, after that, the shrinkage distortion produced during spot welding of fillet-structural section mainly contributes the large dustpan deformation of the thin-wall weldment; increasing temperatures, enlarging loads and prolonging the hold time can improve the shape correction of the thin-wall weldment during post weld heat treatment, hence the guide maps of the post weld heat treatment for shape correction of the thin-wall weldment under 700 and 750 degrees C are worked out.
关键词	thin-wall part of TA15 titanium alloy weld deformation post weld heat treatment finite element method
收录类别	SCI
语种	英语
WOS研究方向	Metallurgy & Metallurgical Engineering
WOS类目	Metallurgy & Metallurgical Engineering
WOS记录号	WOS:000372691500004
出版者	SCIENCE PRESS
引用统计	被引频次：2[WOS] [WOS记录] [WOS相关记录]
文献类型	期刊论文
条目标识符	http://ir.imr.ac.cn/handle/321006/121850
专题	中国科学院金属研究所
通讯作者	Lu Shanping
作者单位	1.Chinese Acad Sci, Shenyang Natl Lab Mat Sci, Inst Met Res, Shenyang 110016, Peoples R China 2.AVIC Shenyang Aircraft Corp, Shenyang 110034, Peoples R China
推荐引用方式 GB/T 7714	Li Yongkui,Quan Chunyi,Lu Shanping,et al. STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT[J]. ACTA METALLURGICA SINICA,2016,52(3):281-288.
APA	Li Yongkui,Quan Chunyi,Lu Shanping,Jiao Qingyang,Li Shijian,&Sun Zhonghai.(2016).STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT.ACTA METALLURGICA SINICA,52(3),281-288.
MLA	Li Yongkui,et al."STUDY ON SHAPE CORRECTION OF THE THIN PLATE OF TA15 TITANIUM ALLOY BY POST WELD HEAT TREATMENT".ACTA METALLURGICA SINICA 52.3(2016):281-288.