Ring Rolling Forming and Properties of Ti2AlNb Special Shaped Ring Prepared by Powder Metallurgy

doi:10.11900/0412.1961.2019.00015

IMR OpenIR

	Ring Rolling Forming and Properties of Ti2AlNb Special Shaped Ring Prepared by Powder Metallurgy
	Lu Zhengguan 1,2; Wu Jie 1; Xu Lei 1; Cui Xiaoxiao 1; Yang Rui 1
通讯作者	Xu Lei(lxu@imr.ac.cn)
	2019-06-11
发表期刊	ACTA METALLURGICA SINICA
ISSN	0412-1961
卷号	55 期号:6 页码:729-740
摘要	Ti2AlNb alloy was considered as the candidate material to replace superalloys such as GH4169 in gas turbine engine applications due to higher strength-weight ratio at elevated temperatures. Powder metallurgy (PM) offers the potential for solving many of the problems associated with the large ingots, such as center-line porosity and chemical inhomogeneity. In order to study the feasibility of preparing Ti2AlNb special shaped ring with large size, PM + ring rolling combined process is considered as a potential method and discussed in this work. PM Ti2AlNb alloy and special shaped ring (D>800 mm) with a nominal composition of Ti-22Al-24.5Nb-0.5Mo (atomic fraction, %) were prepared from pre-alloyed powder using hot isostatic pressing (HIP). Hot compression tests of PM Ti2AlNb alloy and wrought alloy with the same chemical composition were conducted on Gleeble-3800 testing machine under 930 similar to 1050 degrees C and 0.001 similar to 1 s(-1) conditions. Ring rolling was conducted on PM Ti2AlNb special shaped ring by horizontal rolling machine, and the microstructure evolution and properties performance of PM ring after rolling forming process were studied. The results show that the processing window for PM Ti2AlNb alloy is broader than that for wrought alloys, and wrought Ti2AlNb alloy is easier to crack at low temperature or relative high strain rate. PM Ti2AlNb alloy has more homogeneous chemical composition and uniform alpha(2) phase distribution. Stress instability phenomenon of PM Ti2AlNb alloy is more obvious than that of wrought alloy which is related to phase transition of Ti2AlNb alloy. Optimized deformation temperature for PM Ti2AlNb special shaped ring was set as 1030 similar to 1045 degrees C with reference to the hot compression results. Ti2AlNb special shaped ring after two rolling steps has no any kinds of defects presented by X-ray testing, ultrasonic testing and fluorescence detection. O laths inside PM Ti2AlNb alloy become shorter and narrow, and alpha(2) phase tends to be a coarser and spherical structure due to the hot deformation. After a typical heat treatment (980 degrees C, 2 h, AC + 830 degrees C, 24 h, AC), nearly B2 + O microstructure is obtained in Ti2AlNb special shaped ring. Compared with the undeformed alloy, tensile ductility at room temperature and 650 degrees C of Ti2AlNb ring after hot deformation improves due to the refined O phase structure.
关键词	Ti2AlNb powder metallurgy hot isostatic pressing ring rolling forming
DOI	10.11900/0412.1961.2019.00015
收录类别	SCI
语种	英语
WOS研究方向	Metallurgy & Metallurgical Engineering
WOS类目	Metallurgy & Metallurgical Engineering
WOS记录号	WOS:000468415300006
出版者	SCIENCE PRESS
引用统计	被引频次：4[WOS] [WOS记录] [WOS相关记录]
文献类型	期刊论文
条目标识符	http://ir.imr.ac.cn/handle/321006/133553
专题	中国科学院金属研究所
通讯作者	Xu Lei
作者单位	1.Chinese Acad Sci, Inst Met Res, Shenyang 110016, Liaoning, Peoples R China 2.Univ Sci & Technol China, Sch Mat Sci & Engn, Shenyang 110016, Liaoning, Peoples R China
推荐引用方式 GB/T 7714	Lu Zhengguan,Wu Jie,Xu Lei,et al. Ring Rolling Forming and Properties of Ti2AlNb Special Shaped Ring Prepared by Powder Metallurgy[J]. ACTA METALLURGICA SINICA,2019,55(6):729-740.
APA	Lu Zhengguan,Wu Jie,Xu Lei,Cui Xiaoxiao,&Yang Rui.(2019).Ring Rolling Forming and Properties of Ti2AlNb Special Shaped Ring Prepared by Powder Metallurgy.ACTA METALLURGICA SINICA,55(6),729-740.
MLA	Lu Zhengguan,et al."Ring Rolling Forming and Properties of Ti2AlNb Special Shaped Ring Prepared by Powder Metallurgy".ACTA METALLURGICA SINICA 55.6(2019):729-740.