Texture and yielding anisotropy of Zircaloy-4 alloy cladding tube produced by cold Pilger rolling and annealing

IMR OpenIR

	Texture and yielding anisotropy of Zircaloy-4 alloy cladding tube produced by cold Pilger rolling and annealing
	Liu, CZ; Li, GP; Chu, LH; Gu, HF; Yuan, FS; Han, FZ; Zhang, YD; Li, GP (reprint author), Chinese Acad Sci, Inst Met Res, 72 Wenhua Rd, Shenyang 110016, Liaoning, Peoples R China.
	2018-03-14
发表期刊	MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
ISSN	0921-5093
卷号	719 页码:147-154
摘要	Crystal orientation and mechanical properties of Zircaloy-4 (Zr-4) alloy cladding tube manufactured by cold Pilger rolling and annealing were systematically investigated. Electron Back-Scattered Diffraction (EBSD) analysis showed that grains, which were fully recrystallized in alpha phase, were strongly oriented with their c axis parallel to the tangential direction (TD) of the tube and, meanwhile, their normal direction of {11 (2) over bar0(}alpha) planes parallel to the axial direction (AD). Compression tests carried out along three loading directions (TD-0 degrees, TD-45 degrees and AD, respectively) at room temperature revealed that the Zr-4 alloy tube exhibit strong yielding anisotropy: TD-0 degrees > TD-45 degrees > AD. Meanwhile, the alloy exhibited strain rate hardening effect, since the yield strength increased with the growing strain rate. The relationship between texture and yielding anisotropy of the Zr-4 alloy tube was further discussed based on Schmid factor theory. The Schmid factor values for basal, prismatic and pyramidal < a > slip systems, which were three important yielding mechanisms in Zr-4 alloy during the compression, were calculated depending on the geometric relationship between loading directions and crystal-lography. Calculation results revealed that there was an inverse relationship between Schmid factor value for slip modes and the compression yield strength of the Zr-4 alloy.; Crystal orientation and mechanical properties of Zircaloy-4 (Zr-4) alloy cladding tube manufactured by cold Pilger rolling and annealing were systematically investigated. Electron Back-Scattered Diffraction (EBSD) analysis showed that grains, which were fully recrystallized in alpha phase, were strongly oriented with their c axis parallel to the tangential direction (TD) of the tube and, meanwhile, their normal direction of {11 (2) over bar0(}alpha) planes parallel to the axial direction (AD). Compression tests carried out along three loading directions (TD-0 degrees, TD-45 degrees and AD, respectively) at room temperature revealed that the Zr-4 alloy tube exhibit strong yielding anisotropy: TD-0 degrees > TD-45 degrees > AD. Meanwhile, the alloy exhibited strain rate hardening effect, since the yield strength increased with the growing strain rate. The relationship between texture and yielding anisotropy of the Zr-4 alloy tube was further discussed based on Schmid factor theory. The Schmid factor values for basal, prismatic and pyramidal < a > slip systems, which were three important yielding mechanisms in Zr-4 alloy during the compression, were calculated depending on the geometric relationship between loading directions and crystal-lography. Calculation results revealed that there was an inverse relationship between Schmid factor value for slip modes and the compression yield strength of the Zr-4 alloy.
部门归属	[liu, chengze ; li, geping ; gu, hengfei ; yuan, fusen ; han, fuzhou ; zhang, yingdong] chinese acad sci, inst met res, 72 wenhua rd, shenyang 110016, liaoning, peoples r china ; [liu, chengze ; yuan, fusen ; han, fuzhou ; zhang, yingdong] univ sci & technol china, sch mat sci & engn, 96 jinzhai rd, hefei 230026, anhui, peoples r china ; [chu, linhua] state nucl baod zirconium ind co ltd snz, baoji 721013, peoples r china ; [gu, hengfei] univ chinese acad sci, 19 yuquan rd, beijing 100049, peoples r china
关键词	Strain-rate Mechanical-properties Schmid Factors Zirconium Zr Deformation Behavior Slip Microstructure Temperature
学科领域	Nanoscience & Nanotechnology ; Materials Science, Multidisciplinary ; Metallurgy & Metallurgical Engineering
收录类别	SCI
语种	英语
WOS记录号	WOS:000429390300016
引用统计	被引频次：32[WOS] [WOS记录] [WOS相关记录]
文献类型	期刊论文
条目标识符	http://ir.imr.ac.cn/handle/321006/79433
专题	中国科学院金属研究所
通讯作者	Li, GP (reprint author), Chinese Acad Sci, Inst Met Res, 72 Wenhua Rd, Shenyang 110016, Liaoning, Peoples R China.
推荐引用方式 GB/T 7714	Liu, CZ,Li, GP,Chu, LH,et al. Texture and yielding anisotropy of Zircaloy-4 alloy cladding tube produced by cold Pilger rolling and annealing[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2018,719:147-154.
APA	Liu, CZ.,Li, GP.,Chu, LH.,Gu, HF.,Yuan, FS.,...&Li, GP .(2018).Texture and yielding anisotropy of Zircaloy-4 alloy cladding tube produced by cold Pilger rolling and annealing.MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,719,147-154.
MLA	Liu, CZ,et al."Texture and yielding anisotropy of Zircaloy-4 alloy cladding tube produced by cold Pilger rolling and annealing".MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 719(2018):147-154.