纯钛半球形零件拉深回弹影响因素分析

IMR OpenIR

	纯钛半球形零件拉深回弹影响因素分析
其他题名	Analysis on drawing springback influencing factors for pure titanium hemispherical part
	高恩志 1; 陈文超 1; 李作成 1; 孔德诚 1
	2018
发表期刊	锻压技术
ISSN	1000-3940
卷号	43.0 期号:012 页码:57-61
摘要	以0.6mm厚TAO纯钛薄板为研究对象,建立了符合实际的半球形零件拉深及回弹有限元模型,对半球形纯钛薄壁件拉深回弹过程进行了数值模拟研究,分析了工艺参数对回弹量的影响规律,并进行了相关的试验验证。结果表明:回弹量随着摩擦系数的增加而减小,摩擦系数小于0.14时,回弹量减少趋势明显,大于0.14时回弹量减少趋势变缓;回弹量随着单位压边力增大而减小,单位压边力小于1.4MPa时,回弹量变化显著,随着压边力的增大,回弹量减少趋势平缓;回弹量随凸凹模间隙的增大而增大。最后,在数值模拟的基础上进行了实际拉深试验,壁厚测试的实际结果与有限元模拟结果基本吻合,回弹后尺寸满足零件尺寸要求。
其他摘要	For TA0 pure titanium sheet with 0.6 mm thickness,the finite element models of actual hemispheric part deep drawing and springbaek were established,and their drawing springback processes were numerically simulated.Then,the related test verifications were conducted,and the influences of process parameters on springback amount were investigated.The results show that the springback amount reduces with the increasing of friction coefficient,and the springback amount decreases obviously when the friction coefficient is less than 0.14.However,when the friction coefficient is larger than 0.14,the springback amount decreases smoothly.Furthermore,the springbaek amount reduces with the increasing of unit blank holder force,and the springback amount changes significantly when the unit blank holder force is less than 1.4MPa.With the increasing of blank holder force,the springback amount decreases smoothly,and the springbaek amount increases with the increasing of clearance between punch and die.Finally,the actual drawing test is conducted on the basis of numerical simulation,the results of wall thickness test are basically consistent with the finite element simulation results,and the dimension after springback meets the size requirements of parts.
关键词	TA0半球件拉深数值模拟回弹量摩擦系数
收录类别	CSCD
语种	中文
CSCD记录号	CSCD:6399393
引用统计	被引频次：3[CSCD] [CSCD记录]
文献类型	期刊论文
条目标识符	http://ir.imr.ac.cn/handle/321006/142410
专题	中国科学院金属研究所
作者单位	1.沈阳航空航天大学 2.中国科学院金属研究所
推荐引用方式 GB/T 7714	高恩志,陈文超,李作成,等. 纯钛半球形零件拉深回弹影响因素分析[J]. 锻压技术,2018,43.0(012):57-61.
APA	高恩志,陈文超,李作成,&孔德诚.(2018).纯钛半球形零件拉深回弹影响因素分析.锻压技术,43.0(012),57-61.
MLA	高恩志,et al."纯钛半球形零件拉深回弹影响因素分析".锻压技术 43.0.012(2018):57-61.