| Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF | |
| Lu, Yuxian1,2; Zhang, Hao1; Xue, Peng1; Wu, Lihui1; Liu, Fengchao1; Jia, Luanluan3; Ni, Dingrui1; Xiao, Bolv1; Ma, Zongyi1 | |
| Corresponding Author | Zhang, Hao(haozhang@imr.ac.cn) ; Ni, Dingrui(drni@imr.ac.cn) |
| 2023-06-01 | |
| Source Publication | CRYSTALS
 |
| Volume | 13Issue:6Pages:14 |
| Abstract | Laser powder bed fusion (LPBF) is a typical additive manufacturing technology that offers significant advantages in the production of complex components. With the rapid heating and cooling characteristics of LPBF, a large amount of solid solution of alloying elements in the matrix can be achieved to form supersaturated solid solutions, thus enhancing the properties of LPBF alloys. For the unique microstructure, the heat treatment process needs to be adjusted accordingly. In this work, a Zr/Sc-modified Al-Mg alloy processed by laser powder bed fusion (LPBF) with relatively low cost and good mechanical properties was investigated. The fine microstructure was obtained under rapid solidification conditions. The nanoscale Al-3(Sc,Zr) particles precipitated at the molten pool boundary during solidification. These particles, as effective heterogeneous nucleators, further refined the & alpha;-Al grains and improved the mechanical properties of the alloy. As a result, the alloy exhibited a heterogeneous microstructure consisting of columnar grains in the center of the molten pool and equiaxed grains at the boundaries. The rapid solidification resulted in the supersaturation of solute atoms in the & alpha;-Al matrix, which significantly enhanced the solid solution strengthening effect. With the LPBF processing parameters of a combination of a laser power of 250 W, a laser scanning speed of 833 mm/s, and stripe scanning mode, the tensile strength of the alloy reached 401.4 & PLUSMN; 5.7 MPa, which was significantly higher than that of the cast alloys with aging treatment (281.1 & PLUSMN; 1.3 MPa). The heat treatment promoted the formation of secondary Al-3(Sc,Zr), Mn/Mg-rich phases. The ultimate tensile strength and elongation at fracture after aging at 325 & DEG;C for 2 h were 536.0 & PLUSMN; 1.7 MPa and 14.8 & PLUSMN; 0.8%, respectively. The results provide insight into the preparation of aluminum alloys with relatively low cost and excellent mechanical properties. |
| Keyword | additive manufacturing laser powder bed fusion Al-Mg-Sc-Zr alloy fine grain strengthening solution strengthening |
| Funding Organization | National Key Research and Development Program of China ; National Natural Science Foundation of China ; Youth Innovation Promotion Association, CAS ; Bintech-IMR Ramp;D Program |
| DOI | 10.3390/cryst13060913 |
| Indexed By | SCI |
| Language | 英语 |
| Funding Project | National Key Research and Development Program of China[2022YFB3707400] ; National Natural Science Foundation of China[U21A2043] ; Youth Innovation Promotion Association, CAS[2022191] ; Bintech-IMR Ramp;D Program[GYY-JSBU-2022-010] |
| WOS Research Area | Crystallography ; Materials Science |
| WOS Subject | Crystallography ; Materials Science, Multidisciplinary |
| WOS ID | WOS:001017060500001 |
| Publisher | MDPI |
| Citation statistics | |
| Document Type | 期刊论文 |
| Identifier | http://ir.imr.ac.cn/handle/321006/178442 |
| Collection | 中国科学院金属研究所 |
| Corresponding Author | Zhang, Hao; Ni, Dingrui |
| Affiliation | 1.Chinese Acad Sci, Inst Met Res, Shi Changxu Innovat Ctr Adv Mat, Shenyang 110016, Peoples R China 2.Univ Sci & Technol China, Sch Mat Sci & Engn, Shenyang 110016, Peoples R China 3.Binzhou Inst Technol, Shandong Key Lab Adv Aluminum Mat & Technol, Weiqiao UCAS Sci & Technol Pk, Binzhou 256606, Peoples R China |
| Recommended Citation GB/T 7714 | Lu, Yuxian,Zhang, Hao,Xue, Peng,et al. Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF[J]. CRYSTALS,2023,13(6):14. |
| APA | Lu, Yuxian.,Zhang, Hao.,Xue, Peng.,Wu, Lihui.,Liu, Fengchao.,...&Ma, Zongyi.(2023).Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF.CRYSTALS,13(6),14. |
| MLA | Lu, Yuxian,et al."Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF".CRYSTALS 13.6(2023):14. |
| Files in This Item: | There are no files associated with this item. | |||||
Items in the repository are protected by copyright, with all rights reserved, unless otherwise indicated.
Edit Comment